Arm-electronics DVRCD120 Manuel d'utilisateur

Version 1.5 00P379216RSEA5 Full-Featured MPEG-4 DVR User’s Manual Ver. 1.5

User’s Manual 9 2.1 Position the Unit Firstly, note to position / mount the Full-featured MPEG-4 DVR in a proper place and be sure to powe

User’s Manual 10 Connecting Short-term Device If you plan to install any short-term devices to the Full-featured MPEG-4 DVR and use them as p

User’s Manual 11 Camera Looping Plenty of BNC connectors are positioned on the real panel for looping out the video input. LAN Connector (

User’s Manual 12 RS-232C The unit provides a RS-232C communication port for sending and receiving signals. USB Connector (x2) There are two USB

User’s Manual 13 3.1 Front Panel Introduction The unit’s front panel controls enable user to control the unit and preset the programmable fu

User’s Manual 14 3.1.2 Functional Keys The Full-featured MPEG-4 DVR functional keys on the front panel for normal operation are described as

User’s Manual 15 JOG/SHUTTLE The jog/shuttle knob, shown as below figure, is a combination of a shuttle ring with an embedded jog disk, whic

User’s Manual 16 • Inside the shuttle ring is the jog disk, shown as the figure, it can turns completely in either directions. O

User’s Manual 17 PLAY/STOP Press this key to switch between live image and playback video. NOTE: The video of latest 5 ~ 10 minutes

User’s Manual 18 NOTE: Please go to the <Password> menu to enable or disable the password protection. NOTE: For Full-featured MPEG-4

User’s Manual 1

User’s Manual 19 The color bar and system checking information will be shown on the monitor and disappear when the unit has been completely p

User’s Manual 20 Administrator Password User Password 1234 4321 NOTE: It is strongly suggested to change the passwords to prevent unauthor

User’s Manual 21 3.5.1 Set Date / Time Set Date / Time Select <Date> / <Time> and press ENTER for adjusting the settings. LEFT

User’s Manual 22 3.5.2 Daylight Saving Time Daylight Saving Time The item is for those people who live in certain regions to observe Daylig

User’s Manual 23 3.6.1 Record Mode The Record Mode is for selecting resolution and recording rate. The relative record settings, such as

User’s Manual 24 3.6.3 Preset Record Configuration The <Preset Config> is used to select the preset recording quality and frame rate.

User’s Manual 25 3.6.5 To Record Event Video Only If you want your DVR unit to start recording only under the alarm is triggered, follow t

User’s Manual 26 4.1.2 Digital Zoom Users are able to view a 2× full screen in live mode. To view the 2× full screen, follow the steps. •

User’s Manual 27 4.1.4 Viewing Recorded Video To view recorded video, user can press PLAY/STOP key directly. When press the PLAY/STOP ke

User’s Manual 28 Pause Playback and Single Step Forward To pause and resume recorded video, follow these steps. • Press one of the CHANNEL keys

User’s Manual 2 Caution and Preventive Tips • Switch the 115/230V selector to your local voltage standard • Handle with care, do not drop the

User’s Manual 29 Press CALL key for 3 seconds, the BNC Monitor will be given the same function as the VGA Monitor, except Playba

User’s Manual 30 4.2.2 Sequence with Call Monitor Users are allowed to use the Full-featured MPEG-4 DVR front panel to control a

User’s Manual 31 4.3.1 Searching by Time Follow the steps to search video by date and time. • Press SEARCH key to enter the Search menu; th

User’s Manual 32 Follow these steps to search event video through Event List: • Press SEARCH to enter the Search menu. • To search event video

User’s Manual 33 From the Main menu, select <Video Export> and press ENTER. The menu is displayed. Video Export 1. Select Device 2. Se

User’s Manual 34 4.4.1.2 Select Video for Exporting After selecting video clips, set the item <Begin Export> to <YES> and press E

User’s Manual 35 4.4.1.3 Digital Signature User can export video clip with or without a digital signature. Set the item to <YES> to

User’s Manual 36 4.4.2.1 ezBurn Introduction Built with the ezBurn technology, ezBurn function provides users the easier way to export

User’s Manual 37 No exportable device detected. Please install the target device/media to the DVR. Enter: Retry ESC: Exit • Press EN

User’s Manual 38 The first three items are used to select the data that you want be purged. The items are described as follows. After select the

User’s Manual 3 Important Information Before proceeding, please read and observe all instructions and warnings in this manual.

User’s Manual 39 4.6.2 Dome Protocol Setup The Dome Protocol item lists the available dome protocols for communicating with dome cameras

User’s Manual 40 4.6.3 RS485 Setup Full-featured MPEG-4 DVR controls the domes via RS-485 communication protocol. The RS-485 parameters of Fu

User’s Manual 41 4.6.4 Dome Controlling Key The function keys used in Dome Control are described as follows. Set / Go Preset This key is

User’s Manual 42 Auto / Enter • In OSD Menu mode, the key is used to make selection. • In dome control mode, this key is used to activate au

User’s Manual 43 • Press 1 to access the Set/Go Preset function. The Dome Preset menu is displayed. Dome Preset Index 1 2 3 4 5 6 7 Set Pre

User’s Manual 44 Appendix A: Technical Specifications All specifications are subject to change without notice. Feature \ Product 16 CH Model 8

User’s Manual 45 Recording Quality 8 levels presets, adjustable Image Size 2K to 20K Byte/picture Storage Mode Linear/ Circular Playback

User’s Manual 46 Appendix B: Alarm I/O Definition 4/8 Channel Model: 16 Channel Model: Pin Definition Pin Definition P

User’s Manual 4 Table of Contents 1. Overview ...

User’s Manual 5 4.3 Searching Recorded Video...30 4.3.1 Sear

User’s Manual 6 1. Overview The Full-featured MPEG-4 DVR is an integrated digital video recorder that combines the features of a time-

User’s Manual 7 • Three USB2.0 ports for video clip export and/or backup • Easy software upgrade via USB ThumbDrive®, DVD+RW, or In

User’s Manual 8 RECIR10 1 1 12 13 1 4 1592 3 4 5 6 71 816REWFF/PLAYSTEPSEQFREEZE PLAY/STOP MODESEARCH MENU 2. System Setup The notices and