Arm-electronics MP13DVPDN Manuel d'utilisateur Page 1

00P3H210MZSEB2 1.3 Megapixel Vandal Proof IP Dome Camera User Manual Ver2.2

95. Installation Please read the instructions provided in this chapter thoroughly before installing the vandal proof IP Dome Camera. 5.1 Power an

10 5.2 Hard Ceiling The vandal proof IP Dome Camera can be installed directly on a wall or ceiling. Please note that the wall or ceiling must have en

11Figure: Dome Camera Unit Detached Step 5: Refer to the diagram and mark the positions of the four screw holes at the chosen installation location

12 Step 8: Fasten the Dome Camera housing with the four equipped screws. Step 9: Thread the power and Ethernet cables through either the side condui

13Step 10: Attach the snap-on module into the Dome Camera housing. NOTE: The terminal blocks should face the side conduit entry, as shown in the fig

14 Step 13: Rotate the lens to adjust the camera's zoom level and focal length. Adjust the zoom ring screw to set the desired zoom; subsequent

155.3 4S Mount Electrical Box Before installing the IP Dome Camera in the electrical box, please unscrew and open the dome cover with the Security T

16 STEP 5: Connect the power and Ethernet cables to their connectors on the Dome Camera unit. STEP 6: Attach the snap-on module into the Dome Camera

176. Accessing Camera For initial access to the IP Dome Camera, users can search the camera through the installer program: DeviceSearch.exe, which ca

18 Device Search Step 3: Click “Device Search” again, and all the finding IP devices will be listed in the page, as shown in the figure below. The

1Table of Contents 1. Software Version ...3 2.

19The default login ID and password for the Administrator are: Login ID Password Admin 1234 NOTE: ID and password are case sensitive. NOTE: It is

20 Step 3: Click “OK” on the Note of setting change. Wait for one minute to re-search the IP Dome Camera. Step 4: Click the “Device Search” butto

21 Step 5: Enter User name and Password to access the IP Dome Camera. Installing DC Viewer Software Online For the initial access to the IP Dome Ca

22 Then the security warning window will pop up. Click “Install” to carry on software installation. Click “Finish” to close the DC Viewer window whe

237. Configuration & Operation The IP Dome Camera is provided with a user-friendly browser-based configuration interface, and a free bundled CMS

24 There are five tabs: Home, System, Streaming, Camera and Logout on the top panel. Home Users can monitor live video of the targeted area. System

257.2 Home Page In the Home page, there are several function buttons right down the displayed image. Screen Size Adjustment Image display size can

26 7.3 System Related Settings The figure below shows all categories under the “System” tab. Each category in the left column will be explained in t

277.3.1 Host Name and System Time Setting Press the first category: <System> in the left column; the page is shown as below. Host Name The

28 7.3.2 Security Click the category: <Security>, and the page is shown as the figure below. Root password Change the administrator’s passwo

2 7.4.5 Privacy Masking Function...61 7.4.6 Audio Mode and Bit Rate Settings...

29• I/O access Please refer to 7.3.7 Application for alarm configuration. • Camera control This item allows the appointed User to change camera

30 7.3.3 Network Click <Network> in the left column, and the page will display as shown below. Users can choose to use fixed IP address or

31Get IP address automatically (DHCP) The camera’s default setting is “Use fixed IP address”. Please refer to the previous section Chapter 6. Accessi

32 When using static IP address to login to the IP Dome Camera, users can access it either through “DeviceSearch” software (see Chapter 6. Accessing

337.3.4 DDNS Dynamic Domain Name System (DDNS) allows a DNS name to be constantly synchronized with a dynamic IP address. In other words, it allows t

34 Password/Key Enter the password or key required by the DDNS provider for authentication. 7.3.5 Mail The Administrator can send an e-mail via Simp

357.3.6 FTP The Administrator can set as sending alarm message to a specific File Transfer Protocol (FTP) site when an alarm is triggered. Users can

36 7.3.7 Application (Alarm Settings) The IP Dome Camera equips one relay input and one relay output for cooperating with alarm system to catch even

37Action (Multi-option) The Administrator can specify alarm actions that will take when the alarm is triggered. All options are listed as follows: •

38 address. NOTE: Make sure SMTP or FTP configuration has been completed. See section 7.3.5 Mail and 7.3.6 FTP for further details. File Name Ent

31. Software Version The IP Dome Camera’s current software version is as follows: Released Version Oct., 2008 d20081013NS

39• Add sequence number suffix (limited value) File Name: imageXX.jpg X: Sequence Number The file name suffix will end at the number being set. For

40 7.3.8 Motion Detection Motion Detection function allows detecting suspicious motion and triggering alarms when motion volume in the detected area

41Motion Detection Setting Users could adjust various parameters of Motion Detection in this section. • Sampling pixel interval [1-100]: The defau

42 • Upload Image by E-Mail Select this item, and the Administrator can assign an e-mail address and configure various parameters as shown in the

43 NOTE: Make sure SMTP or FTP configuration has been completed. See section 7.3.5 Mail and 7.3.6 FTP for further details. File Name The uploaded i

44

457.3.9 Snapshot The IP Dome Camera supports MJPEG snapshot function. Users can specify a storage location for the snapshots. The default setting is:

46 7.3.10 Iris Adjustment (Box Camera and Vandal Proof Dome) Users could adjust auto iris lens when different lens is selected to install on the cam

477.3.11 View Log File Click on the link to view the system log file. The content of the file provides useful information about configuration and co

48 7.3.12 View User Information The Administrator can view each added user’s login information and privileges (see 7.3.2 Security). View User Login

4 2. Overview The vandal proof IP Dome Camera features a 1.3 Megapixel progressive scan image sensor that delivers unparalleled image quality. Utiliz

49 As the figure above shows: User: 1:1:0:1 1:1:0:1= I/O access : Camera control : Talk : Listen (see 7.3.2 Security) Therefore, it denotes the

50 7.3.13 View Parameters Click on this item to view the entire system’s parameter setting.

517.3.14 Factory Default The factory default setting page is shown as below. Follow the instructions to reset the IP Dome Camera to factory default s

52 7.3.15 Software Version The current software version is displayed in the software version page, which is shown as the figure below.

537.3.16 Software Upgrade Software upgrade can be carried out in the “Software Upgrade” page, as shown below. NOTE: Make sure the upgrade software

54 NOTE: Do not change the upgrade file name, or the system will fail to find the file. Step 2: Pull down the upgrade binary file list and select

55 After the upgrade process is finished, the viewer will return to Home page, and operation can continue. 7.4 Video and Audio Streaming Settings

56 7.4.1 Video Resolution and Rotate Type The video setting page is shown below: Video Resolution The IP Dome Camera provides various video dua

57Video Rotate Type Users can change video display type if necessary. Selectable video rotate types include Normal, Flip, Mirror and 180 degree. Diff

58 7.4.2 Video Compression Users can select a proper MJPEG/MPEG-4 compression mode in the video compression page (see the figure below), depending on

52.2 Package Contents Please check the package contains the following items listed below. Vandal Proof IP Dome Camera Self Tapping Screws Power

597.4.3 Video OCX Protocol In the Video OCX protocol setting page, users can select RTP protocol using UDP or TCP transport, for streaming media ove

60 7.4.4 Video Frame Skip Video frame skipping is for saving bandwidth, if necessary. The setting page is shown as below. MJPEG/MPEG-4 Frame Skip

617.4.5 Privacy Masking Function Users can setup maximum two privacy masks in the selected areas to avoid any intrusive monitoring. The Mask setting

62 Mask Cancel Uncheck either Mask1 or Mask2 or both to cancel the mask(s). Help Page A Mask Description page is provided for your reference during

637.4.6 Audio Mode and Bit Rate Settings The audio setting page is show as below. In the Audio page, the Administrator can select one transmission m

64 • Simplex (Listen only) In the Listen only Simplex mode, the local/remote site can only listen to the other site. • Disable Select the item to

657.5.1 Exposure Setting The exposure is the amount of light received by the image sensor and is determined by the width of lens diaphragm opening

66 7.5.2 White Balance Setting A camera needs to find reference color temperature, which is a way of measuring the quality of a light source, for c

677.5.3 Backlight Setting Based on various lighting situations, users could select to turn on or off the function of backlight compensation to opti

68 7.5.7 Digital Zoom Setting The camera’s digital zoom is adjustable from x1 to x12 at VGA resolution. Press <SET> to confirm the new setti

6 3. Introduction of the IP Dome Camera This chapter will provide the camera dimensions for reference before installation. Definition of each connec

698. CMS Software Introduction The IP Dome Camera bundles Central Management System (CMS) software. Offering powerful functionalities via intuitive

70 Appendix A: Technical Specifications Camera Image Sensor 1/3" Sony progressive CCD 1/3.8" Sony progressive CMOS Picture Elements 1280

71Mechanical User Account 20 Power 3 Pins Terminal Block Pitch: 3.5mm Ethernet 180D RJ-45 with LED Audio 5 pins terminal block, Pitch 2.54mm Conn

72 Appendix B: Internet Security Settings If ActiveX control installation is blocked, please either set Internet security level to default or change

73ActiveX Controls and Plug-ins Settings Step 1~3: Refer to the previous section above. Step 4: Down the page, press “Custom Level” (see the figure

74 Step 5: Under “ActiveX controls and plug-ins”, set ALL items (as listed below) to <Enable> or <Prompt>. ActiveX controls and plug-ins

75Appendix C: DC Viewer Download Procedure The procedure of DC Viewer software download is specified as follows. Step 1: In the DC Viewer installat

76 Step 3: Click “Finish” to close the DC Viewer installation page. Then, the IP Dome Camera’s Home page will display as follows:

73.2 Camera’s Connectors The diagram below shows the vandal proof IP Dome Camera’s reset button and various connectors. Definition for each connector

8 4. System Requirements To perform the IP Dome Camera via web browser, please ensure your PC is in good network connection, and meet system requirem